← All articles

Modular kitchen mistakes to avoid when planning

The planning mistakes we see most often in modular kitchens, from clashing drawers to missing sockets, and the simple checks that prevent each one.

Couple cooking together in a home kitchen

Kitchen mistakes are rarely dramatic. Nobody installs a kitchen upside down. Instead, it is a drawer that only opens halfway because it hits the oven handle, a socket hidden behind the fridge or a corner cabinet full of things nobody can reach. Small problems, repeated several times a day, for years.

The frustrating part is that almost every one of these is avoidable. They happen because a decision was skipped, rushed or made in the wrong order. Once the cabinets are built and the countertop is fixed, fixing them is expensive or impossible.

Here are the mistakes we see most often, and what to do instead.

Mistakes in the order of planning

1. Designing before choosing appliances

The most common mistake is designing the cabinets first and buying the fridge, hob, chimney, oven and dishwasher later. Then the fridge is wider than its space, the oven door clashes with a drawer and the hob does not fit the cut-out.

Instead: choose your appliances, or at least their exact sizes, before the design is finalised. Draw them into the plan at real size, including door swings. Our chimney and hob guide covers the decisions that affect cabinet sizes and the duct route.

2. Ignoring clashes between doors and drawers

On paper, everything fits. In real life, the dishwasher door blocks a drawer, two corner drawers collide or the fridge door cannot open fully against a wall.

Instead: ask to see the 3D design with every door and drawer shown open. Check corners in particular. If two things hit each other, it is far cheaper to fix in the drawing than on site.

3. Too few sockets, in the wrong places

Mixer, kettle, toaster, microwave, water purifier, chimney, fridge, dishwasher and a phone charger. Most kitchens need more points than people expect, and they need them exactly where each appliance will sit.

Instead: list every appliance, decide where it lives and mark the socket on the drawing before tiling. Add a couple of spare points along the counter for things you will buy later. All electrical work should be done by a licensed electrician.

Mistakes in counter and storage

4. No landing space beside the hob and fridge

A kitchen can have plenty of counter in total and still have nowhere to put down a hot pressure cooker next to the hob, or a bag of groceries next to the fridge.

Instead: keep a clear stretch of counter on at least one side of the hob, the sink and the fridge. These landing zones get used constantly.

A kitchen is judged by the space you can use in the middle of cooking, not the total length of counter on the drawing.

5. Heavy things stored overhead

Plates, glass jars and pressure cookers in wall cabinets look tidy on a plan. In daily use, they mean lifting heavy, sometimes fragile things above your head several times a day.

Instead: keep heavy items in deep drawers below the counter, between knee and waist height. Use wall cabinets for light, everyday items such as glasses, mugs and spices.

6. A wasted corner

A blind corner with only a shelf becomes a dark, deep cave. Things go in and are forgotten.

Instead: plan the corner deliberately. Use a carousel or swing-out corner fitting, or rearrange the layout so the corner holds something you rarely need. Ask to see the mechanism working with weight on it before you choose.

Mistakes in materials, hardware and ventilation

7. The wrong board near the sink

The sink cabinet faces leaks, splashes and wet vessels every day. A carcass made from a board that swells with water will fail first, often within a few monsoons.

Instead: use a higher water-resistant grade or a waterproof material for the sink cabinet, and make sure cut edges are sealed. Our guide to plywood, MDF and HDHMR explains which board goes where.

8. Saving money on hardware

Hinges, drawer runners and lift mechanisms are the moving parts of a kitchen. Cheap hardware sags, sticks and loosens long before the shutters wear out.

Instead: if the budget is tight, choose a simpler shutter finish and keep good hardware. Ask for full-extension, soft-close runners on the drawers you will use most.

9. Forgetting ventilation until the end

A chimney added as an afterthought often ends up with a long, twisting duct that barely works, or a recirculating unit in a kitchen that badly needs extraction.

Instead: decide the chimney position and duct route before the wall cabinets are designed. Plan the shortest path to the outside.

10. Choosing finishes only for the showroom

A deep, high-gloss shutter looks stunning in a showroom under perfect light. At home, near the hob, it shows every fingerprint and splash of oil.

Instead: choose finishes for the life they will have. Matte or textured finishes on lower cabinets hide marks. Save gloss for wall cabinets or a feature area.

Mistakes in light and future-proofing

11. Poor task lighting

A single ceiling light leaves you chopping in your own shadow.

Instead: plan under-cabinet lighting along the full counter, and place ceiling lights over the front edge of the counter rather than behind you.

12. Leaving no room for change

Families grow, cooking habits shift and new appliances arrive. A kitchen packed to the last centimetre has no room for any of it.

Instead: leave one cabinet flexible, add a spare socket or two and keep a section of counter clear rather than filling every gap with a fixed fitting.

A final check before you approve

  1. Every appliance drawn at real size with doors open
  2. A socket marked for each appliance, plus spares
  3. Clear landing space beside the hob, sink and fridge
  4. Heavy items planned below the counter
  5. The corner solved
  6. Water-resistant board at the sink
  7. Hardware specified clearly in the quotation
  8. Chimney duct route drawn
  9. Task lighting on the full counter

Most of these come down to planning in the right order, which is exactly what we set out in how to plan a modular kitchen.

If you would like someone to check your kitchen drawings for these mistakes before you sign off, tell us about your project.

Keep reading

More from the blog.